International ServiceMaxx 2017 diagnostic and programming service tool J1939\J1708 (Offline)+keygen |

ServiceMaxx version 43.26 (release date 12-09-2015)

ServiceMaxx J1708

• Connection / Communication:
  • 9-Pin Type I (Black)
    • Protocol CAN J1708 # 250K Baud
  • 9-Pin Type II (Green)
    • Protocol CAN J1708 # 250K Baud
• Engine Detection Target:
  • Engine Serial Number
• Supported Legacy Engines (1994 - 2006):
  • Pre-MaxxForce Engines
    • I63BX:3 Box I6 (1994 - 1997)
    • V83BX:3 Box V8 (1994 - 1997)
    • i308:DLC I6 (1998 - 2004)
    • T444E:DLC V8 (1998 - 2004)
    • I313:DLCII I6 (2005 - 2006)
    • V128:DLCII V8 (2005 - 2006)
    • V126:DLCII V6 (2005 - 2006
    •        
    •  
•  

ServiceMaxx version 43.26 (release date 12-09-2015)

ServiceMaxx J1939

• Connection / Communication:
  • 9-Pin Type I (Black)
    • Protocol CAN J1939 # 250K Baud
    • K-line (MWM Engines)
  • 9-Pin Type II (Green)
    • Protocol CAN J1939 # 250K Baud
    • Protocol CAN J1939 # 500K Baud (2016 North American engines forward)
    • KWP2000 K-line (For MWM Engines)
• Engine Detection Target:
  • Engine Calibration ID (Production Calibration only)
  • CAT Engines also use Parameter: 88/01
• Supported Engines:
  • North American
    • v155:MaxxForce 5 (2007 - 2009)
    • v134:MaxxForce 7 (2007 - 2009)
    • v152:MaxxForce 7 (2010 - 2012)
    • v179:MaxxForce 7 (2013 - )
    • i326:MaxxForce DT, 9, 10 (2007 - 2009)
    • i334:MaxxForce DT, 9 ,10 (2010 - 2012)
    • i367:MaxxForce DT, 9, 10 (2013)
    • i766:MaxxForce 11, 13 (2008 - 2009)
    • i783:MaxxForce 11, 13 (2010 - 2012)
    • B764:MaxxForce 11, 13 (2013 - 2013.5)
    • i770:MaxxForce 15 (2010 - 2013)
  • SCR Engines
    • I746:N9, N10 SCR (2014 - )
    • B718:N13 SCR (2013 - 2014)
    • B745:N13 SCR (2015 - )
  • Removed Engines:
    • I63BX:3 Box I6 (1994 - 1997)
    • V83BX:3 Box V8 (1994 - 1997)
    • I308:DLC I6 (1998 - 2004)
    • T444E:DLC V8 (1998 - 2004)
    • V126:DLCII V6 (2005 - 2006)
    • I313:DLCII I6 (2005 - 2006)
    • V128:DLC V8 (2005 - 2006)
• Engine list below is with Engineering Access:
  • Military Engines
    • Mil13:MaxxForce 12.4D
  • CAT Engines:
    • CT11:CAT CT11/13 (2010 - 2012)
    • CT764:CAT CT13 (2013)
    • CT15:CAT CT15
    • CT718:CAT CT13 SCR (2013 - 2014)
    • CT745:CAT CT13 SCR (2015 - )
  • Global Engines:
    • I341:DLCII I6 Export (2007 - )
    • I716:N13 (Euro V)
    • MWM:MaxxForce 3.0H (Euro III - P418V50)
    • MWM:MaxxForce 7.2/4.8 H (Euro III - P625V13)
    • MWM:MaxxForce 7.2/4.8 H (Euro IV - P800V24)
    • MWM:MaxxForce 7.2/4.8 H (Euro IV - P800V32)
    • MWM:MaxxForce 7.2/4.8 H (Euro V - P1090V52)
    • MWM:MaxxForce 3.2 H (Euro III)
    • MWM:MaxxForce 3.2 H (Euro IV)
    • MWM:MaxxForce 3.2 H (Euro V)
  • Engineering Engines:
    • B786N13 (2017 - )
  • Removed Engines (Did not go into Production):
    • I355:MaxxForce 9.3 (Euro V)

Software Fixes:

• Software Lag or Slow response Issue
  • Change the way Requested signals are handled.
• ServiceMaxx version 42.18 (release date: 08/05/2015)
  • Software Enhancements
    • MaxxForce 11/13 (2010 - 2013)
      • DOC Efficiency Test (Field Service Access)
    • MaxxForce DT/9/10 (2010 - 2013)
      • DOC Efficiency Test (Engineering Development)
      • Air Management Performance Test (Engineering Development)
      • Trip Report
      • Remove Trip Report (Not Supported)
    • MaxxForce 11/13 (2010-13), N13 SCR (2014 - 2015)
      • Stand Alone Real Time Clock
      • Time Synchronization Check
      • Multi Cylinder Cutout enhancements
      • Add Start and End temperatures to Test Results
      • Trip Report enhancement
      • Remove MaxxForce name from Report Printout
      • Correct Reset for Trip Active Regen Count
    • N9/N10 SCR (2014 - ), N13 SCR (2013 - 2015)
      • DPF Regeneration session
        • Session update (Move Test Inhibitors to Default view)
    • N13 SCR (2017) Engineering Access only
      • Add database Support: Signals/Parameters/DTCs
    • Snapshot recordings enhancement
      • Remove Min/Max/Average from recordings
      • Remove Negative counter
    • History Support (Phase 1)
      • Writes Engine information to history.
      • Vehicle Identification number
      • Engine Serial Number
      • Calibration ID
      • Customer Password – When entered by user.
    • Slow Network Alert
      • Popup Alert message if slow Network is detected during software updates.
  • Software Fixes
    • Signal display and Recording
      • Display Proper Symbols
      • Display correct value in Graphs
    • MaxxForce 11/13 (2010 - 2013), N13 SCR (2014 - 2015)
      • Multi Cylinder Cutout enhancements
      • Refresh Test Results panel if test is re-started.
      • Test Abort Message Correction
      • High Pressure Pump Test
      • Air Management Test
      • Intake Air Heater Test

 without needing a net JAVA iinternet connection