Ultima Derma Rolling Pen MTS$PMS MYM Microneedling Micro Screw Port Needle Cartridge Device Electric Stamp Tools Wireless | Красота и

Ultima Derma Rolling Pen MTS$PMS MYM Microneedling Micro Screw Port Needle Cartridge Device Electric Stamp Tools Wireless | Красота и

How to operate

Adapter Mode

1. Plug in DC adaptor to the jack.

2. Plug in DC adaptor to AC outlet.

Battery Mode

1. Turn on Dr.pen directly with the fully charged battery.

2. To charge the battery :Plug the adapter into an outlet and connect it to charge. The battery indicator light will illuminate light will illuminate in red .Indicator light will turn green when fully charged.

3. Battery fully charges in about 4 hours.

4. Battery can be charged while working.

HOW TO OPERATE

1. Preparation

2. Take out needle cartridge in the sterilized packing.

3. Fitting round slots 1 into 2 of machine ,push needle cartridge horizontally up to the end.

4. Lock the cartridge by turning it to the counter clockwise.

5. Adjustment of needle length should be done after turn on the machine.

6. I f you want to remove the needle cartridge ,turn it to the clockwise and push out horizontally,fitting round slots(slot 1.slot 20slot) together.

Adjustment of needle length

You can adjust the length of needle by turning the adjustment ring clockwise or counter clockwise. Turning it clockwise ,length of it will be longer. Turning it counter clockwise,length of it will be shorter.

1. Adjustment of speed and needle length

2. Adjustment of Speed and ON/OFF

3. 5Speed level control

Pressing the switch 2 seconds to open the device,it starts from the lowest speed to highest speed when you turn on the power firstly.The speed cycles low to high.Please press the switch 2 seconds when you need to stop the device.

The flicker frequence of light faster,the speed is higher.

REFERENCE CHART

SPECIFICATION

1. 
   Object

Apparatus for applying a Micro-needle Therapy by vibration

1. Preformance

A device for puncturing skin-penetrating drugs or cosmetics supports with a micro-needle guided between extended and retracted positions.

1. Classifications

-Type of protection against electric shock:class equipment.

-Degree of protection against electric shock:Floating Applied Part

-Degree of protection against the ingrees of water :Ordinary

Equipment(ixpo)

-Mode of operation :Continuous operation

Packing list

Host :1pcs

Cartrudges:2pcs 12pins

Manual :1pcs

Adapter:1pcs

[Operation]
Point method:
After the nanocrystal chip is mounted on the nanocrystal wafer and vertically touches the surface of the skin, it can be visually observed that there is a slight depression, and the speed, denseness, and gentleness are raised one by one. Adjust the strength according to the contact area
Sliding method:
After the nanocrystal chip is mounted on the nanochip, it is perpendicularly contacted with the skin surface, and a slight depression can be visually observed to slide in a straight line. While sliding, the nano wafer does not leave the skin surface, and the same part is recommended to stay for 3-5 seconds and the number does not exceed 2 Times.
Circle method:
After the nanocrystal chip is mounted on the nano-wafer and perpendicular to the surface of the skin, the sensation of the depression can be visually observed, and the nano-wafer does not leave the surface of the skin at the same time, and the same part is recommended to stay 3 - less and the number of times is less than 2 times.Various problem skin use steps and product recommendations
Dry, sensitive skin:
Before using various functional products, introduce the hydrating product (hyaluronic acid hydrating mask) three times before, and then introduce the functional product after the skin is not dehydrated.
Introduce a small range before introducing a functional product, and use it on the entire face without symptoms such as redness, itching, etc.
Please use the no-clean type hydrating products in time after import.
Spotted problem skin:
It is recommended to use acne essence with hydrating products (such as whitening column spot) to use acne-prone skin:
It can be introduced with acne products. The acne skin itself has inflammation. It is recommended not to use it all over the face when importing. It should only be introduced at the acne area to avoid infection of other parts of the face.
Acne acne print introduction Note:
It can be introduced with acne products in combination with lyophilized powder. First use the lyophilized powder to introduce the acne marks. When importing, you should bypass the acne operation to avoid infection, and finally introduce the acne products vertically on the acne.
Specific operation methods of acne pit:
After cleansing, use the instrument to pick up the acne pit, then apply the lyophilized powder in the acne pit and lift it with the instrument until the acne pit is red or slightly painful. It is introduced twice a week, and the lyophilized powder is applied every morning and evening. Generally, it is more effective for more than three months.

【Instructions】
1. Cleans the skin: daily makeup remover, cleansing, can be cleaned twice with toner.
2. Remove the nanochip and mount it on top of the crystallizer.
3. Apply a proper amount of stock solution or serum to your face.
4. Press and hold the power switch for 3 seconds to start the crystallizer and touch the surface of the skin vertically. It is recommended to stay for 3 to 5 seconds for each contact point.
5. After the operation, please turn off the power and remove the nano-wafer, apply the common skin care products, it is recommended to use the essence, cream and so on. (It is better to make a no-clean mask before applying skin care products)
6. Nano-wafers are not reusable to avoid secondary pollution. Please discard them after use.